AVAILABLE PRODUCTS

DigiShot Detonators
Downline Lengths
Feet	Meters	Units per box
20	6.1	84
30	9.2	66
50	15.2	42
60	18.3	36
80	24.4	30
100	30.5	24
120	36.6	18
150	45.7	18
160	48.8	12
180	54.9	12
245	74.7	12
All lengths are packed in a case with dimensions of 445 x 295 x 205mm with a 1.1B shipping classification.

DigiShot Control Equipment
Product Code	Material Description	Base Unit
302860	DigiShot Blaster USB Cable Charger Synchronized Cable	SET 1 1 1
302999	DigiShot Tagger USB Cable Tagger to Detonator Connector Adapter	EA 1 1
303160	SmartKey	EA
303193	DigiShot Tagger Set Tagger USB Cable Tagger to Detonator Connector Adapter Carry Case	SET 2 2 2 1
303263	Tagger to Detonator Connector Adapter	EA
202593	Synchronized Cable	EA

TRANSPORTATION, STORAGE AND HANDLING

DigiShot must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. Control equipment and accessories should be handled with due care and not dropped, mishandled, subjected to excessive vibration or exposed to any chemical agents. Connectors should be kept clean and the equipment must be kept in a safe environment to avoid misappropriation or misuse.

TECHNICAL DATA

Detonator
Dynamic Shock Resistance	>31,830psi or 2.19 x 108 Pa
ESD Resistance	Passes CEN TS 13763-27 & SANS 1717-1
Detonator Shell	Copper
Detonator passes tests specified in Standard SANS 1717-1 and CEN 13763	SANS 1717-1: The South African National standards for: The design and approval of EDD initiation systems for use in mining and civil blasting applications. CEN 13763-27: European CEN-Testing specification for Explosives for civil uses – Detonators and relays.
Detonator Strength	#8 (South African Strength Definition) #12 (North American Strength Definition)
Base Charge	PETN
Net Explosives Quantity (NEQ)	1gm/detonator
Timing	Programmable
Wire	Rugged, red, over extruded
Connector	Rugged, water resistant
Tensile Strength	>550 N / 124 lbs
Detonator Shell Marking	Dangerous – Blasting Cap - Explosive Danger – Detonateur - Explosif
In-Hole Sleep time (Polyethylene)	At least 7 days (when tested in 100% diesel, 500Kpa pressure and starting temperature of 60°C/140°F - end temperature of 25°C / 177°F)
Accuracy	± 1ms for blasts durations of less than 5 seconds
Detonator Temperature Limits	-40°C to +70°C -40°F to +158°F

Packaging
UN Shipping Classification	1.1B (manufactured in South Africa) 1.4B (manufactured in America)
Detonator Configurations	Shrink wrapped Coil
Cable Colour	Red
Connector	Transparent

System Limits
Max no of rows	63 Rows
Max no of Decks supported	15 Decks
Maximum Total Delay Time	20 000 milliseconds
Maximum Number of Detonators (Single Blaster mode)	300
Maximum Number of Detonators (Synchronized mode)	2 Blasters may be linked together for blasts up to 600 detonators, using a DigiShot Sync Cable (Next release – 3 Blasters will be linked together for blasts up to 900 DigiShot Detonators using a special Dual DigiShot Sync Cable).
Maximum Number of Detonators (serial mode)	The blaster may also be fired from a serial port but in this case only 1 blaster can be connected (300 detonators) and no synchronized operation is possible.
Maximum Lead-in wire plus surface harness	Should not exceed 2500m
Maximum Number of synchronized Blasters	2 (Next release – 3 Blasters)
In-hole Lead Length options	20 ft, 30 ft, 50 ft, 60 ft, 80 ft, 100 ft, 120 ft, 150 ft, 160 ft***, 180 ft***, 245 ft***. (*** Maximum numbers of Detonators per blast will reduce if average in-hole lead length exceeds 150 ft)